As requested by the company Husqvarna AB, we have developed a prototype of an electrical start device to a chainsaw. This was done through the development of new details in Catia, which has been integrated with existing details. Electrical components have been purchased by HAB electronics. In parallel with the modeling calculations was done, which was the basis for determine dimensions and the choice of an electric motor and gears. Prototype 1 improved gradually and led to prototype number 2, which became the final result.

This work covers a broad analysis of the risks that could impact the achievement of electrical safety of electrical installations. The work includes both electrical equipment such as the installation of electrical equipment.The report illustrates the main technical characteristics of electrical connections greater than 10 mm2 and provides an introduction to the crimping systems for copper and aluminum conductors. In addition to that analyzes the factors that are important to assure the quality of an electrical connection throughout the value stream in terms of both materials such informations. Furthermore analyzed deeper the need for skills development of technicians and other staff.The different parts of this work are analyzed and presented, in theory to studies carried out both at Elpress AB and partly with the help of other scientific reports dealing with similar subjects. In addition, presents a survey that will help understanding the current perception of the electrical connections and cable crimping systems among end users.

Formulation and testing of a new type of chainsaw lubricantThe company Agro Oil has come up with the idea of developing an environmentally adapted chainsaw lubricant with a new unusual base fluid. A field test with a tree-harvester shows unsatisfactory low temperature properties and high wear. In this work the viscosity, price and pour point of different combinations of the given base fluid and three other base fluids have been investigated. Desired viscosity and price are determined for different formulations. The new lubricants tested show lower pour points than almost all products on the Swedish market.A test equipment has been developed to investigate the wear.

Mechanical relays are more and more being replaced with semiconductortechnology. In this thesis it is investigated if and how the larger loads couldbe controlled by transistors. The main part of this work aims to create andverify a solution that can control the starter motor, as well as protect it incase of any failure. The different malfunctions that the solution protectsagainst is high current, too high peak current, low current, maximum cranktime and minimum cool off time. The timers also protect indirectly againstoverheating of the starter engine.The transistors used are BTS555, from Infineon.

The use of chainsaws in both private forestry and commercial companies is highly associated with personal injuries and accidents with deadly outcome. As a result to this, a driver?s license for chainsaws was presented in the year 2005. To get the license you have to attend a course given by the Swedish Forest Agency or one of several private educators. This study is an evaluation of one course given by the Swedish Forest Agency in Uppsala.

A cattle producer that buys calves that are younger than six months to the herd should have a starter stable to prevent infection spreading in the herd. According to the Swedish animal welfare regulation there has to be a starter stable if more than 50 calves that are younger than four months are bought in yearly to the herd. The aim of the study was to improve the knowledge about bovine buildings and management of starter stables to obtain optimal weight gain and health of the calves. The hypothesis 1) The younger the calves are when purchased, the higher the calf mortality and 2) Purchasing calves from a high number of herds involves a higher risk of calf health problems and calf mortality were tested in the study. The objective of the study was to give advices by way of presenting ideal solutions of how a starter stable should be constructed and managed. A field study was done during June to September 2008 to collect knowledge and experience from existing starter stables.

A vehicle that carries a person sitting in a wheelchair has been rebuilt. The original vehicle was provided with a petrol engine, hydrostatic drive and a mechanical steering rod, making it noisy and hard to maneuver. The purpose with this project was to convert the vehicle to make it more environmental and easier to drive.A new design has been proposed where an electrical drive has replaced the noisy combustion engine and an electrical motor with joystick control has replaced the manual steering.The project was divided into two parts. One mechanical part where the construction of the drive and steering were to be decided. The other part involved programming the microprocessor and implementation of all the necessary electrical for the control system of the vehicle.

In today?s society, safety in a workplace is an important factor to any organization. Focus on improving the working conditions by making them safer through technology is taking us into a time where we rely on technology to keep us safe. How well developed the technology may be, it is still not enough to keep us entirely from harm. Human error will always be a factor in the human interaction with a workplace.

At nuclear power plants, electrical valve actuators are important for ensuring that the reactor core is water covered and the pressure in the reactor tank and containment is limited. The electrical actuators are provided with overload protection in case of drawing higher current then the motors are rated for. When safety manoeuvres are needed, the overload protection must not trig and cause the valve to stop before completing the manoeuvre. Analyses have showed that the current settings of the overload protection may cause an illegitimate trig at the worst theoretically possible accident. A new method has been developed with conservative assumptions and applies overload protections for all electrical valve actuators at the three reactors in Forsmark..

E-Series 450 is a chainsaw designed by Husqvarna AB to the semi-professional user. Husqvarna is a world leader when it comes to chainsaws, trimmers, lawn mowers and garden tractors. The problem in hand can be addressed by the question. ?How easy can we start a chainsaw? The purposehas been to provide a solution to the question above and give Husqvarna a good base of which they can continue towards a finished product.

E-Series 450 is a chainsaw designed by Husqvarna AB to the semi-professional user. Husqvarna is a world leader when it comes to chainsaws, trimmers, lawn mowers and garden tractors. The problem in hand can be addressed by the question. ?How easy can we start a chainsaw? The purposehas been to provide a solution to the question above and give Husqvarna a good base of which they can continue towards a finished product.

Modern technology and fast development of heat pumps, the hunt for savings in energy consumption and the strive for environmentally friendly energy sources, convenience, and financial profit, have made heat pumps a reasonable alternative for the heating of houses.When the heat pump starts it will consume a considerable amount of current, which may result in a short-lived voltage-drop if the power grid is weak compared to the start-up current.The company Fortum Distribution which owns and administrates electrical network is interested in an investigation that deals with heat pumps affect on the quality of electricity.The purpose of this investigation is to study fast electrical fluctuations (flicker) as a result of start-up currents for single as well as multiple heat pumps on the same electrical station and from this evaluate whether there will be any problems installing heat pumps..

This thesis is   focused on identifying and documenting all   electrical equipment, such as devices, power lines / cables, and connectors in the facility and also on presenting a brief   technical description and information of the systems around the reactors.   Furthermore there will be a brief description of LabVIEW - which is a   graphical programming language- and which devices / elements   are programmed. For further notification, I am not   responsible for the programming of the devices in LabVIEW   which I have only used as a tool in my work. The plant   for production of biogas consists of four reactors   of which the third reactor (Lakbädden)   is connected to another reactor (UASB)   where they cooperate with each other.   The reactors are used for producing   biogas in the form of methane gas.The reactors I and II are   connected to, various electrical devices as, flow meters, temperature   sensors, frequency converter and   more.

SEP Modular Armoured Tactical System is the next generation of military vehicles developedby BAE Systems Hägglunds AB. At present time, BAE Systems Hägglunds AB aredeveloping a 6-wheel electrical hybrid and a conventional 8-wheel vehicle. The questionformulation was summarized as: ?In which ways can the electrical transmission in a hybriddriveline for SEP be designed, when the surrounding fixed interfaces are kept and the unity ofcomponents within SEP is maximized??. The purpose of this master thesis was to study avariety of concepts for hybrid propulsion.

Abstract: This report covers primarily the work of documenting electromagnetic fields generated by one of the later parts in the electrical power distribution chain: The electrical substation, wherein 10 kV is transformed to 400 V for use by private consumers. Thus it is one of the most widespread and frequently occurring parts in the Swedish power grid and of particular interest, as electrical substations are found everywhere in populated areas, often in close vicinity to people and animals.The report deals with a number of formulated questions and/or hypothesis? stated at the onset of the work undertaken, theory that is relevant for the topics the report covers, the details of the field work undertaken and the following analysis of the readings, which in term provide answers for the questions stated in the beginning. It also covers what is the currently known short term and long term risks associated with electromagnetic fields in the power frequent spectrum and of varying intensity in the vicinity of humans.The analysis also provides recommendations and identifies several points to carefully consider when planning for new installations or replacements of some parts of existing installations.For enhanced reading comprehension there is, aside from sections with pictures and attached explanatory texts and templates, several graphs, one-line diagram and maps of the power grid among the appendixes to the rapport..